Quick Start
Quick Reference Setup Guide
CLUB-8000
This quick reference guide is provided to help you set up your
CLUB-8000 system for the first time. It contains instructions
on setting up the products that are included in the CLUB-
8000. If you are connecting any additional gear that is not
included in the CLUB-8000, refer to the appropriate manuals
for detailed instructions.
Gathering Package Contents
The first step to putting together your new CLUB-8000 system is unpacking all of the necessary equipment. Remem-
ber to keep your manuals nearby when setting up, as you may need to reference them. The products listed below are
included in the CLUB-8000 system:
CDG-9000 PRO
VSP-M1 Multi-Effect Digital Signal Processor/Mixer
• 1 Control interface connector wire
• [1] Instruction Manual
• 1 Instruction manual
SS-88 Speaker Stands
• [4] SS-88 speaker stands
KJM-8000+ 9-Channel Digital Key Control KJ/DJ Mixer
• [1] Instruction Manual
CLUB-8 Road Case
• [1] CLUB-8 road case
• [1] Rolling cart
VP-2100 PRO 2000W Professional Power Amplifier
• [1] Instruction Manual
• [2] MK-38 PRO microphones
• [1] Gooseneck DJ light
• 1 RCA to 1/4” Patch Cable (3.3 ft paired)
• Rack-mounting screws
VX-15 Vocal Speakers
• [4] VX-15 speakers
Mounting components into the CLUB-8
Below is one way to configure your CLUB-8000:
Follow these basic guidelines when mounting:
• Always screw in the mounting screws using an “X” forma-
tion.
• If possible, to keep the products cooler, leave some space in
between the components in the rack.
1
3
4
CDG-9000 PRO CONTROLLER
KJM-8000+ MIXER
2
CDG-9000 PRO PLAYER
VP-2100 PRO AMPLIFIER
On the web at www.vocopro.com
or call toll free 1-800-678-5348
CDG-9000 PRO player unit to KJM-8000+
2
You have the option of either connecting each deck of the CDG-9000 PRO separately (Fig. 1) or together through a single
SWITCHED output (Fig. 2).
Separately through individual deck outputs (Fig.1)
Using RCA cables:
1. For each deck, connect the L/R (red & white) audio outputs and Video (yellow) output on the CDG-9000 PRO to the
CDG(1) and DVD(3) inputs on the rear panel of the KJM-8000+
CDG-9000 PRO Player
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
LD(3)
Together through SWITCHED output (Fig. 2)
CDG-9000 PRO Player
Using RCA cables:
1. Connect the L/R SWITCHED audio and
SWITCHED video outputs on the CDG-9000
PRO player to the CDG(1) audio input on the
KJM-8000 PRO
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
KJM-8000+ to VP-2100 PRO
3
You can do this using either XLR(f) to XLR(m) cables or XLR(f) to ¼”(m) cables. Below are instructions for each.
Using two XLR(f) to XLR(m) (Fig.1)
Using two XLR(f) to ¼”(m) (Fig. 2)
1. Connect the XLR(f) end to the LEFT MASTER AUDIO
XLR output on the KJM-8000+ and the XLR (m) end to
the left XLR audio input on the VP-2100 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000+ and the
right XLR audio input on the VP-2100 PRO
1. Connect the XLR(f) end to the LEFT MASTER AUDIO XLR
output on the KJM-8000+ and the ¼”(m) end to the CH. B
¼” audio input on the VP-2100 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000+ and the CH.
A ¼” audio input on the VP-2100 PRO.
-BRIDGE+
-BRIDGE+
CH
2
CH
1
CH
2
CH
1
STEREO
50Hz ON
VP-2100 PRO Amplifier
STEREO
50Hz ON
THROUGH
THROUGH
THROUGH
THROUGH
MONO
BRIDGE
30Hz OFF
MONO
BRIDGE
30Hz OFF
LOW CUT
FILTER/
LOW CUT
FILTER/
MODEL
VP-2100PRO
MODEL
VP-2100PRO
SPEAKER OUTPUTS
BALANCED INPUTS
SPEAKER OUTPUTS
BALANCED INPUTS
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000+ Mixer
LD(3)
LD(3)
VP-2100 PRO to VX-15 speakers
4
VP-2100 PRO Amplifier
Speakers 1 and 2
-BRIDGE+
CH
2
CH
1
Using the SPEAKON style to ¼” adapter and ¼”(m) to
¼”(m) cable (included):
STEREO
50Hz ON
THROUGH
THROUGH
MONO
BRIDGE
30Hz OFF
LOW CUT
FILTER/
1. Connect the SPEAKON style end to CH.1 on the rear
panel of the VP-2100 PRO
MODEL
VP-2100PRO
SPEAKER OUTPUTS
BALANCED INPUTS
2. Connect one end of the ¼” cable to the ¼” end of the
adapter
3. Connect the other end of the ¼” cable to one of the
four VX-15’s.
3. Repeat this for the second speaker, except now connect
the SPEAKON style end to CH. 2 on the VP-2100 PRO and
the ¼” end to the second VX-15 speaker.
Speakers 3 and 4
VX-15 Speaker #1
VX-15 Speaker #2
Using a ¼”(m) to ¼”(m) cable
VX-15 Speaker #3
VX-15 Speaker #4
1. Connect one end of the ¼” cable to the open ¼” jack
on the rear of speaker 1
2. Connect the other ¼” end to the back of the 3rd
speaker.
3. Repeat this for the final speaker now going from the
back of speaker 2 and into the 4th speaker.
Connecting Microphones to the KJM-8000+
5
Using either a mic cable with two XLR ends (Fig. A) or an XLR to ¼” cable (Fig. B):
Connect the microphone cables to the MIC inputs on the rear panel of the KJM-8000+.
CDG(1)
DVD(2)
CDG(1)
DVD(2)
LD(3)
KJM-8000+ Mixer
LD(3)
Adding the VSP-M1 to the CLUB-8000 system
6
Using either a mic cable with two XLR ends or an XLR to ¼” cable:
1. Connect the XLR(f) end to the LEFT BALANCED OUTPUT on the rear panel of the VSP-M1.
2. Connect the XLR(m) or ¼” end to MIC input 1 on the rear panel of the KJM-8000+.
3. Follow the above steps, now going from the RIGHT BALANCED OUTPUT on the VSP-M1 to MIC input 2 on the rear panel
of the KJM-8000+.
4. Connect the mics to the mic inputs on the rear panel of the VSP-M1.
VSP-M1 Processor
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
LD(3)
|
Teledyne Power Supply HPS 10 User Manual
Terraillon Pedicure Spa IPX4 User Manual
Topcom Network Router BR 604 User Manual
Toshiba DVR KV DVR User Manual
Trimble Outdoors GPS Receiver SPSX51 User Manual
Tripp Lite Network Cables S054 31I User Manual
Tripp Lite Surge Protector DG206 User Manual
Turbosound Portable Speaker TQ 230 User Manual
Tyco Network Card EIOC User Manual
Volvo Car Stereo System 1992 240 User Manual